No Function Lumix G9
Be sure you set the camera's USB mode to PC(Tether). My G9 works using this setting. However, there is no geotagging. I see that there's a footnote about geotagging working "with some limitations". The app says geotagging is not supported on the G9, and that's NOT my expectation from the "with some limitations" features listing.
Please update your firmware. Whenever there's a Firmware update available, you'll see a red notification badge on the menu icon in the bottom left corner of the app. Follow this notification badge through the app to get to the firmware update screen.
App menu (bottom left) → Unleashed with gear icon (bottom left) → tap on your Unleashed (near top ) → tap "Firmware"
Scroll down and tap "Install Update". With the Unleashed M, you need to keep the camera awake, so that the Unleashed stays powered during the entire update. To keep the camera from entering standby, half-press the cameras's shutterbutton continuously or regularly until the update is done. This only takes a little over a minute.
We added Geotagging for Panasonic fairly late, so you'll need to be on Firmware version 3.0.0 or later. We always recommend installing the latest update!
Did you follow the instructions to set up your camera as described here?
https://www.foolography.com/start/
PANASONIC LUMIX
App menu (bottom left) → Unleashed with gear icon (bottom left) → tap on your Unleashed (near top ) → tap "Firmware"
Scroll down and tap "Install Update". With the Unleashed M, you need to keep the camera awake, so that the Unleashed stays powered during the entire update. To keep the camera from entering standby, half-press the cameras's shutterbutton continuously or regularly until the update is done. This only takes a little over a minute.
We added Geotagging for Panasonic fairly late, so you'll need to be on Firmware version 3.0.0 or later. We always recommend installing the latest update!
Did you follow the instructions to set up your camera as described here?
https://www.foolography.com/start/
PANASONIC LUMIX
- Set the camera setting: MENU > Setup > IN/OUT > USB > USB Mode = PC(Tether)
- Set the camera setting: MENU > Setup > IN/OUT > USB > USB Power Supply = OFF
Founder & CEO of Foolography, Hardware & Firmware developer.
Hi,
we issued another firmware update for the Unleashed this week. Could you install that and try again?
Whenever there's a Firmware update available, you'll see a red notification badge on the menu icon in the bottom left corner of the app. Follow this notification badge through the app to get to the firmware update screen.
App menu (bottom left) → Unleashed with gear icon (bottom left) → tap on your Unleashed (near top ) → tap "Firmware"
Scroll down and tap "Install Update". With the Unleashed M, you need to keep the camera awake, so that the Unleashed stays powered during the entire update. To keep the camera from entering standby, half-press the cameras's shutterbutton continuously or regularly until the update is done. This only takes a little over a minute.
we issued another firmware update for the Unleashed this week. Could you install that and try again?
Whenever there's a Firmware update available, you'll see a red notification badge on the menu icon in the bottom left corner of the app. Follow this notification badge through the app to get to the firmware update screen.
App menu (bottom left) → Unleashed with gear icon (bottom left) → tap on your Unleashed (near top ) → tap "Firmware"
Scroll down and tap "Install Update". With the Unleashed M, you need to keep the camera awake, so that the Unleashed stays powered during the entire update. To keep the camera from entering standby, half-press the cameras's shutterbutton continuously or regularly until the update is done. This only takes a little over a minute.
Founder & CEO of Foolography, Hardware & Firmware developer.
After much fussing and several failed attempts, I was able to update the firmware. The GPS icon shows an X despite the app having location permission. Phone is a Google Pixel 7a.
- Attachments
-
- Failed update attempt 4 - Unleashed always had power - connection would be lost and I'd have to restart each time
- Screenshot_20240404-153736.png (132.58 KiB) Viewed 786 times
-
- GPS status after update
- Screenshot_20240404-152558.png (135.49 KiB) Viewed 786 times